How can we help you today?

You can override the automatic system using either the Pool App which is self-explanatory


or, if you have Manual Buttons on the Intelligent Pool Controller Cabinet, you can do the following:


 

INTELLIGENT POOL CONTROLLER CABINET (f you have lighted push-buttons)


NORMAL OPERATION

  1. The normal condition for the Pooled Energy System is that the GREEN light on the cabinet should be FLASHING and this means that it is communicating with the Network Operating Centre and is enabled in AUTO mode.
  2. If the GREEN light is STEADY, This means the controller has lost communications with the Network Operating Centre but is enabled in local mode and running whatever program was last loaded into it by the Network Operating Centre.
  3. To shut the whole system down to STAND-BY, press and hold the GREEN button for about a second and the GREEN light goes out. This means the entire system is in STAND-BY and not operating any program.
  4. To put the system back to AUTO, press the GREEN button for about a second.  It will go steady GREEN and then, after about a minute, flashing GREEN.


IF YOU HAVE A POOL SWEEP

  1. The ORANGE light on the cabinet should normally be OFF.  This means that the powered sweep is enabled in AUTO mode.
  2. To stop the sweep for removal from the pool or to clean it or for any other reason, press the ORANGE button for about one second.  The ORANGE light come ON and this means the sweep is in STAND-BY.
  3. To enable the sweep, press the ORANGE button so that the ORANGE light goes out.


TO START THE FILTER PUMP AT ANY TIME,


  1. The GREEN Button will normally be flashing (or steady) GREEN. 
  2. Press and hold the GREEN button for about a second till the GREEN light goes OFF
  3. Press and hold the ORANGE button for >5 seconds
  4. The Filter pump should start


Please note that when you run in manual using this mode, the chlorinator does not operate. Please do not run in manual for more than 8 hours. Use the PARTY or SWIM NOW modes on the Pool App if you wish to run the Filter and Chlorinator at the same time.


TO START THE SWEEP AS WELL, AFTER YOU HAVE STARTED THE FILTER PUMP AS ABOVE

  1. If you have a sweep with its own pump and wish to start it as well, press and hold the ORANGE button again for >5 seconds
  2. To stop the pump(s) and switch back to AUTO, press the GREEN button again


TO EMPTY WATER FROM THE POOL MANUALLY VIA THE FILTER

  1. Press and hold the GREEN button for about a second till the GREEN light goes OFF
  2. Rotate the valve on top of the filter from FILTER to BACKWASH.  If there is an additional valve in the Backwash line, open it.
  3. Press and hold the ORANGE button for >5 seconds
  4. The Filter pump should start. 
  5. When finished, press the GREEN Button for 1 second till the pump stops
  6. Return the Filter Valve from BACKWASH to FILTER.  If there is an additional valve in the Backwash line, shut it.
  7. If the GREEN button is not lit, please press it for 1 second till it lights.  It will glow STEADY at first and then start to FLASH to show that it is in AUTO


TO CLEAN THE PUMP STRAINER


Please check the Strainer on your filter pump from time to time and before you do a backwash. The Pooled Energy system will often detect blockages in the Strainer or the skimmer box and inform you by email or SMS, but not necessarily when the system is only partially blocked.


  1. If the Strainer needs cleaning, press and hold the GREEN button for about a second till the GREEN light goes OFF
  2. After all the pumps stop, SHUT the valve between the filter pump and the pool if you have one.
  3. If the equipment is below water level, ROTATE the valve on top of the filter from FILTER to CLOSED. 
  4. Open the Strainer cover, remove the basket and clean it. 
  5. Replace the basket.  Close and tighten the strainer lid.
  6. ROTATE the valve on top of the filter from CLOSED to FILTER, and open the valve between the filter pump and pool if you have one.
  7. Press the GREEN button for 1 second until it starts flashing.  The system is now back in AUTOMATIC


TO BACKWASH MANUALLY WITHOUT USING THE POOL APP


  1. Check that the Filter Pump Strainer is clean.  If not, please clean as described above.  
  2. After you have finished, press and hold the GREEN button for about a second till the GREEN light goes OFF
  3. Rotate the valve on top of the filter from FILTER to BACKWASH.  If there is an additional valve in the Backwash line, open it.
  4. Press and hold the ORANGE button for >5 seconds
  5. The Filter pump should start.
  6. After 2 minutes or when the backwash water runs clear in the sight glass, press and hold the GREEN button for about a second till the GREEN light goes OFF.
  7. Rotate the valve on top of the filter from FILTER to RINSE.  
  8. Press and hold the ORANGE button for >5 seconds.
  9. The Filter pump should start.
  10. After 15 seconds of running, press the GREEN Button for 1 second till the pump stops
  11. Return the Filter Valve from RINSE to FILTER.  If there is an additional valve in the Backwash line, shut it.
  12. If the GREEN button is not lit, please press it for 1 second till it lights.  It will glow STEADY at first and then start to FLASH to show that it is in AUTO.
Facebooktwitterpinterestlinkedinmail